Search found 898 matches

by barts
Sun Oct 16, 2011 4:39 am
Forum: Technical - Engines and Boilers
Topic: Schedule 80 pipe?
Replies: 5
Views: 4558

Re: Schedule 80 pipe?

I needed a sched 80 3/8" pipe nipple when I replumbed my boiler.My local plumbing wholesaler did not have it but the hydraulic hose company had it in stock.Cost -under $2 -pretty cheap insurance! I have a saying-"we poor people can only afford to do it once-so do it right the first time!" At least ...
by barts
Sun Oct 16, 2011 12:39 am
Forum: Technical - Engines and Boilers
Topic: Engine/Boiler Recommendation
Replies: 14
Views: 8550

Re: Engine/Boiler Recommendation

To protect the pipe, you can just make it heavier, or lay it close to the hull. Any thing that will hurt the pipe (aside from perhaps knocks getting on and off the trailer) will destroy a spinning prop, so this is much less of an issue than one might think. I find a set of guides that insure that th...
by barts
Sun Oct 16, 2011 12:28 am
Forum: Technical - Engines and Boilers
Topic: Probably a really stupid question....Boiler related
Replies: 1
Views: 2217

Re: Probably a really stupid question....Boiler related

Such "hydronic" boilers are typically not rated for the pressures we need to run our steam boats, and have no provision for the collection and distribution of steam, so they are not suitable.

- Bart
by barts
Sat Oct 15, 2011 4:15 am
Forum: Technical - non Engines and Boilers
Topic: Hotwells - Designs and building
Replies: 14
Views: 12353

Re: Hotwells - Designs and building

Yup - got it exactly. In fact, I used one of these for a while:

http://www.webstaurantstore.com/6-deep- ... 20369.html

Round ones work well as separate oil separators, too.

- Bart
by barts
Sat Oct 15, 2011 4:11 am
Forum: Technical - Engines and Boilers
Topic: Schedule 80 pipe?
Replies: 5
Views: 4558

Re: Schedule 80 pipe?

Schedule 80 pipe is mandatory for all boiler/steam connections. This is because the threaded schedule 40 stuff will fail too easily due to a mechanical mishap. I stick to schedule 80 for the feed connections as well, of course. Inside the boiler, you can use schedule 40 when it is used as tubes. - B...
by barts
Fri Oct 14, 2011 4:44 am
Forum: Technical - Engines and Boilers
Topic: Engine/Boiler Recommendation
Replies: 14
Views: 8550

Re: Engine/Boiler Recommendation

Can you explain the condensation idea a little more. What I think you are saying is that I can take the exhaust steam as supplied by the engine, route it through a pipe that goes sthrough the hull to be cooled by the lake/ocean water and then back into the hull and into a reservoir of some kind. Al...
by barts
Thu Oct 13, 2011 3:18 pm
Forum: Technical - Engines and Boilers
Topic: Engine/Boiler Recommendation
Replies: 14
Views: 8550

Re: Engine/Boiler Recommendation

I am surprised that I can run with that low a horespower. I was guessing I would need a 5hp or better. 5 hp will certainly work, but remember that these engines are driving large, slow turning propellers moving lots of water. This means that steam engines will make more effective use of their limit...
by barts
Thu Oct 13, 2011 3:57 am
Forum: Technical - Engines and Boilers
Topic: Engine/Boiler Recommendation
Replies: 14
Views: 8550

Re: Engine/Boiler Recommendation

1. What size engine should I be contemplating ? The engine should be rated at about 2 hp per ton of boat displacement; a bit more or less works fine. The Tanzer 22 has a displacement of about 3000 lbs, so 3 to 4 hp would work very nicely. Details on the Tanzer 22 are here: http://www.msogphotosite....
by barts
Wed Oct 12, 2011 3:18 am
Forum: Technical - Engines and Boilers
Topic: steel cylinder?
Replies: 23
Views: 12795

Re: steel cylinder?

In hot water pressure washer guise, it would absorb something like 250,000 btu/hr, but I think that could be increased a good deal for steam use. Given the example of the Lamont boiler, my feeling is pumped circulation usage such as a hot water pressure heater is probably optimum for BTU/sq. ft.......
by barts
Fri Oct 07, 2011 4:05 am
Forum: Technical - Engines and Boilers
Topic: steel cylinder?
Replies: 23
Views: 12795

Re: steel cylinder?

I'm sure that someone on this forum could explain it better, but I've been building engines for 35 years and I stay away from stainless because I have had too many bad experiences with it. In my experience: Good things about stainless: * high temperature resistance * many alloys resist corrosion we...