Page 3 of 5

Re: building Panatela

Posted: Thu Mar 25, 2010 6:37 pm
by piet schuurs
I hope not that much as in autum last year
piet

Re: building Panatela

Posted: Sat Mar 27, 2010 3:37 pm
by piet schuurs
The engine of Panatela
120 years old Easton & Johnson 1,5+3x3,5
The first testrun on air

http://www.flickr.com/photos/steamlaunc ... 713587234/

regards piet

Re: building Panatela

Posted: Sun Mar 28, 2010 7:11 pm
by mcandrew1894
Looking Good Piet!

What kind of reversing does it have?....swing eccentric?

Dave

Re: building Panatela

Posted: Mon Mar 29, 2010 2:26 pm
by piet schuurs
Thank you Dave

Reverse is slip reverse. I think thats the same as an swing reverse?

It works, but thats it. Its taking to long to reverse this way.

So, first sail this summer and looking what the faulds are. Then during the winter Iám going to try to make an SLR on her.

For exemple, I have at an alternator on the proppellorshaft. But the shaft rev. are to low.
So I have to fit a smaller pouly on the alternator for more rev's.

I'll think during the summer there is coming up more to do.

regards piet

Re: building Panatela

Posted: Tue Mar 30, 2010 2:45 am
by mcandrew1894
"....I'll think during the summer there is coming up more to do."..


There always is! But remember the reason we build these boats....Man created boats to keep their engines dry! :D

Looks great Piet! Much nicer than my boat.....

Congratulations!

Dave

Re: building Panatela

Posted: Tue Mar 30, 2010 7:28 am
by piet schuurs
Much nicer than my boat.....

Iám, not agree, Dave. They are almost the same but they are just different, its just a matter of teast.
Rushforth looks great!!!!!
And if I look to the plant in Rushforth, Iám jealous.
Mine is a mess, your looks thight and professional.

Piet

Re: building Panatela

Posted: Thu Apr 01, 2010 9:19 am
by mcandrew1894
Your a fine man Piet A fine man indeed.

OK, So When is the launching!?......and more importantly the party afterwoods! :D

Ohh and we want video.....says the pot to the kettle :lol:

Your friend,

Dave

Oh and this coming winter, when you make up the SLR, let me know if you would like some help drawing them out....I'd be glad to help.

Re: building Panatela

Posted: Thu Apr 01, 2010 8:09 pm
by piet schuurs
Heh Dave, we have almost the same boat and both have a compound. Than we must both think about the same way about a launch, dont you think?
Regarding to the SLR. I'll think I start to copy and dubble the origenal excentrics ( the must be right the way the are now ) and lower valve rots.
The new timing, and the link between the two lower and the upper valve rot are my proble.
Thats difficult to figger out for my, a aspeccialy the lenght of the link.
Maybe you can help here, without writing a hole book on this forum.
There are lots of pictures or drawings on the web, but all for one specific engine.
Is there a formule for this?

I like your offer Dave, lots of thanks for that.

Piet

Re: building Panatela

Posted: Thu Apr 01, 2010 11:32 pm
by artemis
There are as many ways to design valve gear as there are books about it. My suggestion is to talk to someone (preferably in something close to your language). I'm acquainted with Rainer Radow who did much of his own engine design (Dr. Eng.). You can find him at http://www.steamboating.de/radow.html and I'm sure he will be happy to help. Tell him I sent you.
Ron Fossum Image

Re: building Panatela

Posted: Fri Apr 02, 2010 3:09 am
by mcandrew1894
Hi Piet,

The length of the link should be about 5 times the throw. Based on my own research
That is what I used when I designed my engine.
I would start with getting the valve events, as they are today, documented.
You can do this with a piece of paper and a pencil by doing a rubbing. From there, you can measure your ports and establish the events.
I would also suggest you run a brake test of the engine as it is today. Then there is no guessing later.

For small engines such as ours, I would keep you exhaust lap small or none at all.
Ray Hasbrouck swore by this.

Dave