Prop shaft diameter ?

For technical tips, questions etc. on all subjects except Engines and Boilers.
Post Reply
ianrichards
Full Steam Ahead
Full Steam Ahead
Posts: 154
Joined: Wed Jan 11, 2017 12:30 pm
Boat Name: Isambard
Location: Calstock, Cornwall, UK

Prop shaft diameter ?

Post by ianrichards » Fri Oct 19, 2018 9:00 am

My hull is now progressing well and as always I have two think two steps ahead.
Considering that my hull is 15’ 3” long and I have a small single cylinder engine, what diameter and material prop shaft should I be looking at.
I do have a propeller that could be suitable and has a 3/4” shaft.
Any advice appreciated.
Thanks
Ian
User avatar
fredrosse
Full Steam Ahead
Full Steam Ahead
Posts: 1905
Joined: Fri Nov 20, 2009 5:34 am
Boat Name: Margaret S.
Location: Phila PA USA
Contact:

Re: Prop shaft diameter ?

Post by fredrosse » Fri Oct 19, 2018 2:37 pm

A 3/4 inch shaft, common steel, or stainless steel, or bronze will be perfectly adequate. For launch type of a couple horsepower a smaller shaft is probably adequate (although the launch I am currently building is 15 horsepower, and 14 feet long, that will have a 1 inch diameter steel shaft) and the 3/4 inch diameter is only needed to provide generally good insurance against bending the shaft when grounding or hitting a big rock while underway!
ianrichards
Full Steam Ahead
Full Steam Ahead
Posts: 154
Joined: Wed Jan 11, 2017 12:30 pm
Boat Name: Isambard
Location: Calstock, Cornwall, UK

Re: Prop shaft diameter ?

Post by ianrichards » Fri Oct 19, 2018 2:44 pm

Br, thanks for that..
Back to the shed ...
User avatar
DetroiTug
Full Steam Ahead
Full Steam Ahead
Posts: 1863
Joined: Fri Nov 27, 2009 5:56 pm
Boat Name: Iron Chief
Location: Northwest Detroit

Re: Prop shaft diameter ?

Post by DetroiTug » Fri Oct 19, 2018 3:26 pm

My two centavos. It depends on a few things. Is it going to be left in the water? Only used occasionaly/rarely, then plain steel is ok, bronze or stainless is better. If it's going to be used a lot, left in the water for extended periods, then use bronze or stainless for sure. If you're using a standard rubber cutless bearing, do not use steel, the shaft will rust and upon removal will destroy the bearing. I used a steel shaft on the tug and after about one season, I had to cut it up to remove it. Regarding size, how is it supported and where? If there is a strut bearing right at the prop, smaller shaft sizes can be used, it's not the torque of the engine that is the issue, its the weight of the hull and the danger of running aground (and you will) and bending the shaft. I use a 1" stainless shaft in the tug which is relatively short and well supported on either end and have had no issues (It has a deadwood and strap to the rudder). I think 1" diameter is really about minimum size.

-Ron
ianrichards
Full Steam Ahead
Full Steam Ahead
Posts: 154
Joined: Wed Jan 11, 2017 12:30 pm
Boat Name: Isambard
Location: Calstock, Cornwall, UK

Re: Prop shaft diameter ?

Post by ianrichards » Fri Oct 19, 2018 3:38 pm

Mmmmm ... more then nags to consider.
Many thanks
Ian
User avatar
Lopez Mike
Full Steam Ahead
Full Steam Ahead
Posts: 1903
Joined: Wed Dec 07, 2011 6:41 am
Boat Name: S.L. Spiffy
Location: Lopez Island, Washington State, USA

Re: Prop shaft diameter ?

Post by Lopez Mike » Fri Oct 19, 2018 7:28 pm

A couple of data points:

My launch is 5 hp at 400 rpm which is 65 ft/lbs on a 1.25" shaft turning an 18 diameter by 24 pitch prop. I think the shaft is oversized.

My 36 foot sailboat has 30 hp at a shaft speed 1400 rpm which is 114 ft/lbs on a 1" shaft turning a 15" diameter by 12 pitch prop. This is typical practice is 20 to 40 ft sailboats.

You ar probably safe with the 3/4" shaft if it's supported properly. I think shaft support is probably more important than torque loads anyway. Don't hit stuff or get a line in the prop and you will be fine.
If you think you are too small to make a difference, try sleeping with a mosquito.
Dalai Lama
ianrichards
Full Steam Ahead
Full Steam Ahead
Posts: 154
Joined: Wed Jan 11, 2017 12:30 pm
Boat Name: Isambard
Location: Calstock, Cornwall, UK

Re: Prop shaft diameter ?

Post by ianrichards » Fri Oct 19, 2018 7:46 pm

Thanks.
Ian
User avatar
Kelly Anderson
Full Steam Ahead
Full Steam Ahead
Posts: 172
Joined: Fri Feb 11, 2011 1:28 am
Boat Name: Vividus
Location: Strasburg, PA
Contact:

Re: Prop shaft diameter ?

Post by Kelly Anderson » Sat Oct 20, 2018 1:53 am

What diameter is your crank shaft?

My boat is 23' long, weighs 3,000 lb., has a 6 plus hp engine, and a 1" stainless steel shaft, and is perfectly happy.

My last boat is 20' long, weighs 1,200 lb., has a 2 hp engine, and a 1-1/4" hollow brass shaft about 6' long which would buckle under full steam until I added a third bearing mid-way. Don't forget that the prop shaft is also under compression pushing the boat along.
It was not easy to convince Allnutt. All his shop training had given him a profound prejudice against inexact work, experimental work, hit-or-miss work.
User avatar
barts
Full Steam Ahead
Full Steam Ahead
Posts: 1066
Joined: Wed Nov 18, 2009 6:08 am
Boat Name: Otter, Rainbow
Location: Lopez Island, WA and sometimes Menlo Park, CA
Contact:

Re: Prop shaft diameter ?

Post by barts » Sat Oct 20, 2018 5:04 am

As you might expect, there is lots of detail about this in boat design books.

One handy method is shaft diameter for Aqualoy or Monel should be 1/17.5 3 bladed prop diameter... so if you're using a 14" diameter prop, a 3/4" shaft would be a bit marginal. If you have a Tobin bronze shaft, the divisor is 14.

This is from Gerr "Boat Mechanical Systems Handbook", which is a great book - highly recommended reading.
https://www.amazon.com/Boat-Mechanical- ... s+handbook

Shaft bearing spacing formulae are there as well.

- Bart
-------
Bart Smaalders http://smaalders.net/barts Lopez Island, WA
ianrichards
Full Steam Ahead
Full Steam Ahead
Posts: 154
Joined: Wed Jan 11, 2017 12:30 pm
Boat Name: Isambard
Location: Calstock, Cornwall, UK

Re: Prop shaft diameter ?

Post by ianrichards » Sat Oct 20, 2018 7:32 am

“Boat Mechanical Systems Handbook” ordered, £9.10 here in the UK
Thanks for the pointer.
Post Reply