Southworth 12" Vertical pumps
- Lopez Mike
- Full Steam Ahead
- Posts: 1903
- Joined: Wed Dec 07, 2011 6:41 am
- Boat Name: S.L. Spiffy
- Location: Lopez Island, Washington State, USA
Re: Southworth 12" Vertical pumps
One of my favorite notions is that we have many beliefs that that we are not aware of. That picture of the pump in service startled me because I have always pictured such pumps mounted horizontally and this taking up a lot of space. And Barbara wonders why I check on here every day!
Mike
Mike
If you think you are too small to make a difference, try sleeping with a mosquito.
Dalai Lama
Dalai Lama
- DetroiTug
- Full Steam Ahead
- Posts: 1863
- Joined: Fri Nov 27, 2009 5:56 pm
- Boat Name: Iron Chief
- Location: Northwest Detroit
Re: Southworth 12" Vertical pumps
Hi Mike(s)
The pumps are 12" tall. The valve and seat is .562" X .875" dia.
Here is a pic from last week. They are actually a bit farther along. All the water valves are made and ready to be assembled. About two hours away from the bottom portion pumping water. I have to re-cut all the O-ring pockets for the piston rod, and get thicker O-rings. They were called out 3/32" deep and the O-rings are 1/16". The diameter was right, but the depth is off by .031" Or am I missing something? Is there some practice I'm unaware of where a small ring/spacer is used in conjunction with an O-ring?
The castings are very good, but the prints need some work. They are all in fractions, machinists don't typically work in fractions, especially with CNC machines. Lots of 688's 343's 156's etc., invites mishap.
-Ron
The pumps are 12" tall. The valve and seat is .562" X .875" dia.
Here is a pic from last week. They are actually a bit farther along. All the water valves are made and ready to be assembled. About two hours away from the bottom portion pumping water. I have to re-cut all the O-ring pockets for the piston rod, and get thicker O-rings. They were called out 3/32" deep and the O-rings are 1/16". The diameter was right, but the depth is off by .031" Or am I missing something? Is there some practice I'm unaware of where a small ring/spacer is used in conjunction with an O-ring?
The castings are very good, but the prints need some work. They are all in fractions, machinists don't typically work in fractions, especially with CNC machines. Lots of 688's 343's 156's etc., invites mishap.
-Ron
- Lopez Mike
- Full Steam Ahead
- Posts: 1903
- Joined: Wed Dec 07, 2011 6:41 am
- Boat Name: S.L. Spiffy
- Location: Lopez Island, Washington State, USA
Re: Southworth 12" Vertical pumps
I run into those weird numbers a lot. For .688, read .6875, etc. The fraction is right and, frankly, most of the time the rounding off difference doesn't make any difference. Working to a half thou. isn't often important.
Mu rule of thumb for O-rings when used as packing is to have the width the same as the ring and the depth (from the bottom of the groove to the rod surface) about 10 percent less than the ring. If you really want to do it 'right'. see your hydraulic supplier and get the seals they use. They have a rectangular shape and a wider contact area. And boy do they stand the pressure!
All of these modern things need a really smooth rod. There is something to be said for packings made of hog ears or whatever the heck they use.
Mike
Mu rule of thumb for O-rings when used as packing is to have the width the same as the ring and the depth (from the bottom of the groove to the rod surface) about 10 percent less than the ring. If you really want to do it 'right'. see your hydraulic supplier and get the seals they use. They have a rectangular shape and a wider contact area. And boy do they stand the pressure!
All of these modern things need a really smooth rod. There is something to be said for packings made of hog ears or whatever the heck they use.
Mike
If you think you are too small to make a difference, try sleeping with a mosquito.
Dalai Lama
Dalai Lama
-
- Full Steam Ahead
- Posts: 936
- Joined: Sat Aug 13, 2011 6:41 pm
- Boat Name: B.N.Y.S.
- Location: Middle Earth
Re: Southworth 12" Vertical pumps
Cheers Ron, it appears I wasn't too far out in my guesswork. They are probably only just a little bigger than I thought.
I usually forget to remove everything 'tell-tale' from my photos, there's often a coffee cup, or a tool, left behind that gives the game away.
I usually forget to remove everything 'tell-tale' from my photos, there's often a coffee cup, or a tool, left behind that gives the game away.
Last edited by Mike Rometer on Fri Jan 25, 2013 8:56 am, edited 1 time in total.
Retirement is about doing what floats your boat!
A BODGE : - A Bit Of Damn Good Engineering.
A BODGE : - A Bit Of Damn Good Engineering.
- DetroiTug
- Full Steam Ahead
- Posts: 1863
- Joined: Fri Nov 27, 2009 5:56 pm
- Boat Name: Iron Chief
- Location: Northwest Detroit
Re: Southworth 12" Vertical pumps
Detail of the shuttle valve.
-Ron
-Ron
- DetroiTug
- Full Steam Ahead
- Posts: 1863
- Joined: Fri Nov 27, 2009 5:56 pm
- Boat Name: Iron Chief
- Location: Northwest Detroit
Re: Southworth 12" Vertical pumps
Still a little tweaking to do. Seems to work very good. I have a video of it pumping water that I will upload in a few.
-Ron
-Ron
Re: Southworth 12" Vertical pumps
Nice work Ron
-
- Full Steam Ahead
- Posts: 340
- Joined: Sat Oct 08, 2011 12:58 am
Re: Southworth 12" Vertical pumps
I think I will need to smoke a cigarette.......
That is so cool !!!!!!!!
Can't wait to get it to play with.
You go Ron !!!!!!
That is so cool !!!!!!!!
Can't wait to get it to play with.
You go Ron !!!!!!
- DetroiTug
- Full Steam Ahead
- Posts: 1863
- Joined: Fri Nov 27, 2009 5:56 pm
- Boat Name: Iron Chief
- Location: Northwest Detroit
Re: Southworth 12" Vertical pumps
Thanks, glad you guys like it.
-Ron
-Ron